login   |    register
Eduard [ MORE REVIEWS ] [ WEBSITE ] [ NEW STORIES ]

In-Box Review
148
Spad XIII Late Production
The long live the new queen

by: Stephen T. Lawson [ JACKFLASH ]

  • 1/48 Eduard Spad XIII

History,

Founded in 1910 the Socie’te pour les Apparreils Deperdussin and bought by Louis Bleriot in 1914 and renamed Socie’te pour Aviation et ses De’rive’s. In 1915 ‘Spad’ designer Louis Bechereau began to design a series of fighter aircraft that would use the Hispano-Suiza engine. And its progressively higher horsepowered models. The Spad XIII was first flown in early August 1917. It became the main French high altitude fighter, using powerplants of up to 220hp. It was also flown by the American, Belgian, British, Czech, Italian, Japan and Siamese Air Services from 1918-1928.

kit type history,

While there were other 1/48 scale plastic kits of the Spad XIII many of the older kits were comprised of Balsa wood as a medium. Both Hawk and Aurora had overly large details with heavy raised and scribed stringers and ribs with raised engraving for decal locations. These were the hallmarks of kits from this era. Previously the finest example of the 1/48 Spad XIII is the DML / Dragon kit issues. Here I will discuss the Eduard’s premier issue kit #8196, its general build up and details often misrepresented due previously to a lack of information. PP = plastic part, PE = photoetch. begin with pre-drilling all rigging pilot and strut locator holes.

Box contents,

87 plastic parts
Photo-etched details
4 camouflage variants
Black & White instruction sheet . If you want colour references you have to go to the Eduard Website and see this kit's instruction sheet in "pdf" format.

The Build,

Pages 1 -2 are the typical Eduard histories in multilanguages and parts maps.

Page 3. If your attempting to build a complete and open engine compartment, before you close up the fuselage halves (B 1 & 3 ) carve out the un-needed forward top deck area of the panels. Also the area of vertical support for the kit radiator. For the fuselage interior walls ( PP B 1 & 3 ) you can paint the interior in linen and wood colours and add the internal bracing wires (crisscrossing the bays) from fine wire. Add the compass (D 21.) Next paint the handle for the carburetor adjustment levers (PE 23 ) to look like stained wood or leave it bright metal , as both types were used. The expended ammunition links chutes (PP D 41 X2) are inserted into their slots in (PP B 1 & 3 ). These chutes were done here in plastic but I wonder why Eduard’s Camel kit also included these in both plastic & PE. But here several years later the go only with plastic parts? Next the Starter Magneto (PP D 33) and spring loaded map board (PE 15) should have a wood backing not metal. The PE map is less than convincing and a paper one should be substituted. Add a scrap piece of sheet plastic to represent a fabric screen / wall for the rear cockpit.

The forward lower firewall Section ( PP C 14 ) has a partial facade of the rear portion of the Hispano Suiza motor and is completed by a second addition (PP D 45 ). The forward portion of the engine bearers (PP C 10 & 13 ) assemble together but lack the outer “wing stiffeners that would be seen of this area is left open. The Eduard kit is very much like the DML / Dragon kit in this respect. At this point you can install an engine compartment with some scratch-building and a resin 200hp Hispano-Suiza from Engine & Things (kit # 48147.) The forward sections of the engine bearers (C 10 X 13.) Check your references for wiring and plumbing. I add plumbing from brass and copper wire /rod and small gauge solder.

Page 4. Here you unite the completed floor assembly and lower wing ( PP D 7 )to the closed fuselage halves (B 1 & 3 ). The cockpit floor ( C 3) should be varnished wood with raised metal details. The top of the main fuel tank is centrally located within the forward third area of C 3 with the fuel gauge provided as a decal or as photoetch (PE 9 ) at its apex. This was either a bubble float in the fuel cap or a stick gauge, both working a gear mechanism on marked levels. A fuel line can be made of solder/flux should lead from the pilot’s left side of the main fuel tank to the port side and forward into the firewall. The seat supports are actually the rear of the engine supports. The rudder bar assembly is molded to the flooring. Not my favorite aspect of this kit. These should be painted along with the oil tank ( also molded to the floor) to look like bare metal. the control column ( D 5 ) and oil tank fillet pipe / vent (D 12 ) are bare metal as well. There should be two pipes leading forward from the oil tank ( D 19 & 31 ) to the rear engine to the oil sump . See your references on these details.

The instrument panel ( PP D 35 ) contains (from left to right) oil & water temperature gauges (PP 26 & 28, PE 11 & 14) decal gauge faces are also provided. Centrally located are the switches for the motor air pump, main & auxiliary fuel tanks, and the manual air pump. Add a metal aircraft manufacture’s plate to the right side/ wing of D 35. The support shelf (PP C 4 ) needs to be slightly beveled at its three outer contact edges to fit into the rear portion of for its eventual contact with C 17. Then insert the oil pressure gauge ( PE 13 ) centrally located and to the right, tachometer (PP D 25 & PE 8 ) and the altimeter (PP D 22 & PE 5, 12 ) per the kit instructions. The two pull rings (PE 4 X 2 ) attached to the underside of the instrument shelf ( PP C 4 ) are cocking handles for the twin Vickers machine guns to be added later. Though they give you two rings they only provide for one installation. One other part is the shelf support rods (PP D 29). I would replace these with painted metal items of a smaller gauge. The ammunition box and empty link chutes ( PP B 8 ) are fitted at this point too.

Page 5. If you use the kit lap belt parts (PE 17, 18, 19, 21 & 22 ) should be annealed then glued in place. This represents the type with the quick release mechanism that was standard on French manufactured aircraft. The seat ( C 21 ) is an mid to late production type and should be painted as if upholstered (stuffed with material and covered) in leather. Next you add the actuation control horns ( D 11 ) to the slot in the rudder / stabilizer ( PP C 15 ). The upper fuselage facade (PP C 17 ) elevators (PP C 1 ) fun and rudder combination (P C 15 ) and undersurface chin pan (PP C 8 ) are brought together. The fuselage pick-up straps ( PE 20 X 2 ) are added at this time.

Page 6. First add the stabilizer struts (PP D 18 X 2 ) for the horizontal tail surface assembly. Now insure that the whole tail assembly is directionally plumb with the fuselage in every respect. Then the radiator / engine crankcase and propeller shaft assembly (PP C 16, 38,& 43). The radiator shroud comes as two models ( PP B 5 or 10 ). The latter ( PP B 10 )is recommended as being a late model profile. The same recommendations follow for the radiator shutters. (PP B 4 or 9). Use (PP B 9 ). The radiator of the Spad XIII was bolted directly to the gear housing of the Hispano-Suiza 200hp. Imagine the vibrations and harmonics that this soldered brass unit was subjected to! No wonder Spad XIII type aircraft were in the hangar an average of more than 30% of the time. Two telescopic sites ( PP D 32 or 36 ) are provided. Two ring sites ( PE 2 X 2 ) are provided but you will only need one. The twin Vicker machine guns (PP C 19X 2) drop into their slots accordingly well. The Spad XIII types built for the Americans seem to have partial shielding covering most of the lower sides of the gun receivers/breeches. See your references. These weapons were a natural metal colour and then give them a wash of flat black and allow to dry. You can add the engine head fairings (PP C 39 & 40 ) here. If you are build this with an exposed engine wait to add the exhaust pipes (PP C 9 7 11). Otherwise go ahead and add them now. The engine side mounted access panels come in two types plastic ( PP C 18 & 20 ) or in photoetch (PE 1 & 3 ).

Now you can begin to install the detailed Hispano-Suiza resin engine mentioned in page 3. In some cases you would insert pins into pre-drilled holes in the resin engine heads and the eight connection ports of the exhaust pipes (B 2 & 3.) Some filling may be needed to allow for the distance of the exhaust port connections and the seated engine. Dry fit and measure carefully before permanently attaching either item. In my case the exhausts will be separate from the engine. If you install this assembly begin completing the wiring and plumbing. The fuel & water plumbing and or fairing (PP D 10, 15, 23 7 24 ) needs to be altered in adding tubing to the engine and radiator. The modified forward area of the upper cowling (PP C 17 ) should reflect a cut out for these ‘pipes.’ Check your references. Three types of windscreens ( PP E 1 -3 ) are provided. But, add them as a last step in the build after an over-all dull / flat coating of the finished build.

Page 7. The socket holes in the wings ‘all’ need to be enlarged slightly. Test fit your kit struts first. Carefully align and attach the cabane struts (PP D 1, 34 & 44 X 2 ) to the upper deck (PP C 17). The fuel tank pressure intake ( PP D 20 ) is mounted to the top wing ( PP B 2 ) The aileron actuation control horns, rods and bell crank assembly ( PP D 6, 7, 8, 9 & 30 X 2 ) is done twice. One for each side of the aircraft. The interplane struts ( PP D 2, 3, 13, 14 & 37 X 2 ) need to be added carefully to keep the top wing plumb and square. Then bring these components together with the fuselage using a ‘Lego’ block jig and let the assembly dry thoroughly. The referenced jig keeps everything lined up correctly. Fabric wrap reinforcement strips seen on the interplane struts can be done by using strips of decal film painted an off white colour.

Page 8. Finally the landing gear I clipped the plastic axle ends off of the axle/spreader bar (A 13) and added brass pins of the appropriate diameter in to predrilled holes. Paint and assemble the under carriage struts (PP C 2 & 5 ) and the axle spreader bar ( PP C 12 ) to the fuselage underside, again insuring that it is plumb and square. The creative rigging of this unit can be functional in keeping the assembly together (even if dropped: “The Voice of Experience.”

Lastly the propeller ( PP C 6 & 7 ) is considered. The kit item are an Eclair Co. profile and the Gremont Co. profile and while there were others, check your references for the aircraft that you have chosen.


Colour scheme specifics by pilot,

Page 9. Sergent Fernand Chavannes, Escadrille SPA.112, August, 1918. Fernand Henri Chavannes was born on April 16th, 1897. He served with N.112, and later with SPA.112, when the unit transitioned from Nieuport to SPAD and was accordingly redesignated. Between February 8th, 1918, and August 22, 1918, he accumulated seven aerial victories. He finished the war as Sous Lieutenant with SPA.176. He lived to be 88, and died on October 5th, 1985 in Paris.

Page 10. Lieutenant Charles Nungesser, Escadrille SPA.65 ( GC.13 ), September, 1918. Charles Nungesser was born on March 15, 1892. He entered the war as a hussar, and didn’t join Escadrille VB.106 until the beginning of 1915, and shortly thereafter, transferred to N.65. After having to shoot down a British fighter that mistook him for a German aircraft (apparently due to the emblem painted on his plane) he had his wings adorned with wide, three-color markings. After transitioning to SPADs, his unit was redesignated as SPA.65. He was wounded on many occasions, and the end of the war some him drained of his strength. Reportedly, he needed to be at times carried into his aircraft by mechanics. He is credited with 43 confirmed and 11 probable kills. He disappeared on May 8th, 1927, in a transatlantic attempt.

Page 11. Adjutant Marius Blanc, Escadrille SPA.81 ( GC.15 ), Summer, 1918. Marius Leon Blanc joined Escadrille SPA.81 as a reserve pilot in January, 1918 with the rank of Adjutant. This unit was formed on December 26th, 1916 at Villacoublay, as N.81. After transitioning to SPAD, the unit became SPA.81 on April, 17, 1917, and was placed under Groupe de Chasse GC.15. The unit was commanded by Lieutenant Adrien Louis Jacques Leps. Due to the adornment of elegant markings that all of the unit’s aircraft carried, the squadron came to be known as ‘Escadrille des Levriers’ – the ‘Greyhound Squadron’ SPA.81 claimed 88 aerial victories over its career.

Page 12. Captaine René Fonck, Escadrille SPA.103 ( GC.12 ), Fall, 1918. René Paul Fonck was born on March 27th, 1894. At the start of the war, he volunteered for the air force, but was attached to the corps of army engineers. He didn't start to fly until February, 1915, with Escadrille C.47. On April 27th, 1917 he was transferred to GC.12, and attached to SPA.103. He developed his own combat tactic: he didn't risk much, and on average, he needed nine rounds for a kill. He was never wounded, and on only one occasion he landed with a damaged aircraft. He gained a total of 126 kills, 75 of which were confirmed, and thus became the leading Allied ace. He never gained the adoration that, for example, Guynemer did. During the Second World War, he was a minister in the Vichy government, and his reputation was tainted by inuendo . He died on June 18th, 1953.

At the front,

The following is an excerpt from recent correspondence with Mr. Alan Toelle. He is probably the finest authority on the French 5 colour camouflage extant. He knows the Spad XIII from rudder to prop boss. Mr. Toelle’s lifetime studies into various licensed built Spad XIII types and the layout of their cockpits are a ‘must-read’ to the builder/ researcher/ devotee.

‘...Mr. Carrick’s drawings of the Spad XIII (the basis for the DML Spad XIII, STL) are in my opinion very accurate - as accurate as they can be at that scale. He did a very conscientious job and knew a lot about the subject...’

‘..I provided him with quite a bit of information and we talked over some issues. The wing tips, however should not show the airfoil when viewed from the end as the spars turned down near the ends and the tip bow was flat in the plane of the leading and trailing edge - as a dinner plate laid upside down...’

‘...As for the subject [Hangar Queens] Spad XIII types were all Hangar Queens, relatively speaking. They were reported out of service more than 30% of the time on average. Motor replacement was very common but they had all kinds of other maintenance problems aside from damage due to operations. A good example is Joe Eastman’s Spad XIII S.15006 (Squadron Aircraft) #19 of the 94th Aero Squadron. The following are extracts from Eastman’s diary:...’

‘July 24,(1918): My Spad after five changes of oil pumps, was again given me to make a practice flight this morning in preparation for the regular patrol at 15:00 this afternoon. I no more than cleared it off the field when something - a connecting rod - broke - smoke blew into the pit, the entire plane shook with vibration, and I was barely able to regain the field again without accident. This was my lot after nearly a week in fussing with the tub (aircraft). Rankin at luncheon told me to take (Squadron Aircraft)#10, which he said was in good condition. Later I learned it was the machine that (Lts.) Coolidge and Sherry has unsuccessfully attempted to use. I went out to it and found it still in the process of repair. I waited until time for the patrol and learned in that time further of its disquieting departure from a machine in good condition. The motor is an unheard - of make; (?) The throttles are offset and require a new technique in manipulation; its gas thumb lever needed a pair of pliers to move; and neither guns nor sights had ever been tested. Although my habitual appearance is one of cow-like docility and temperamental imperviousness. I left the ground in a state of mind that jumps out of a chair when a door is closed above a whisper. After two minutes in the air, I began to gather the evidence of my switchboard (Instrument Panel.) Both the air and oil pressures were less than half the normal figure - and the important little temperature hand was doing a comedy skit in the region of 105 degrees or 25 degrees hotter than is conducive to successful flying. A few minute spent hopefully in pursuit of the patrol failed to influence the gauges for the better. I piqued (a sharp roll with wings at near vertical) for the field and instead of the temperature cooling it continued to augment in its own cheery fashion. The motor stopped firing over Coulommiers, struggled to life, coughed, missed and revolved feebly by turns letting me down nearer and nearer to an unpromising landscape - which by the grace of GOD, I was enabled to clear...Plane #10 received a new motor.’

‘On 28 July (Eastman again tested his own plane #19): My plane is still in the hospital this morning. I would have taken it to the range, but on testing the motor could throttle no more than 900 RPM - so I look forward to trying the guns and a flight this afternoon.’

‘29 July: Motor troubles still beset my can (aircraft.) In the vain hope that it might have changed its mind, I took it for a tour of the field, but was drenched by overheated water as before. The mechanics, with whose business I’m daily growing more acquainted, are changing the radiator. These planes are certainly causing a lot of trouble as compared to the 28's (Nieuport types) which were at least simple to keep on the line.’

‘10 August: My motor still knocks and vibrates which I hope can be remedied. Spark plugs, I hope.’

‘13 August: My plane developed trouble on patrol...the motor was knocking and the oil no longer passed through the glass (gauge.) At that instant there was the gentle rap of a broken connecting rod on its way through the casting and I could go no further.’

‘7 September: It seems that no day is complete without some remark on motors. At supper it was said that the Hispano 220 is valued at $5,000.00. And after today I’m ready to send my sixth, I believe it is, back to the shops, each having an average life of say seven hours flying!...In order to give me an opportunity to test out my fancied troubles, Thorne sent me above on the field patrol last evening, although knocking like mischief, she carried one up to 4,000 meters...Thanks to these interminable annoyances. I’ve several times come to the point where I could hardly trust myself to declare faulty on the ground what I’ve been positive of in the air. Today as the Captain seemed dubious of my report - I had (Lt.) Jeffers try my bus (aircraft) out; but he was glad to regain the field after making a half turn in it. Steam was shooting off the top a foot high.’

And so it went. In a period (discussed) of 75 days, plane # 19 (S.15006) had three motor replacements and was reported as unserviceable on 38 days, which is 50.7% of the time! In addition, it had two forced landings at which point it was condemned.. Alan Toelle
Please note that all statements in italics are added by the writer of the kit review for the reader’s benefit.

References,

Aeroplane Monthly, IPC Magazines Ltd. Vol. 19, #8, Aug. 1991.
American Aces of WWI by Franks, Osprey Pub. 2001.
‘To Capture the Rainbow...’ by S. Lawson, Cross & Cockade Int. Vol. 29, #1, 1998.
‘...Before the Colors Fade’ by D. Eubanks, Cross & Cockade USA Vol.19, #1, 1978.
Lafayette Foundation Archives, Denver Colorado USA.
‘Project Butterfly’ by Hardesty, Hastings, and Toelle, Cross & Cockade USA Vol. 9, and 13, 1972.-
-(Most excellent articles on the French 5 color camouflage patterns.)
Report on Spad XIII S.4377 by A. Toelle, unpublished to date 2006.
Report on Spad XIII S.6625 by A. Toelle, unpublished to date 2006.
Report on Spad XIII S.7689 by A. Toelle, unpublished to date 2006.
Report on Spad XIII S.8340 by A. Toelle, unpublished to date 2006.
Report on Spad XIII S.15295 by A. Toelle, unpublished to date 2006.
Report on Spad XIII S.16594 by A. Toelle, unpublished to date 2006.
SPAD XIII C.1 by C.F.Andrews, Profile #17, 1965.
SPAD XIII C.1 by J.M.Bruce , Windsock Datafile #32, Albatros Pub. 1992.
‘The Charge of the Yellow Ram ( the138th Aero Sqdn)’by S. Lawson, Cross & Cockade Int. Vol.25, #4, 1994.
Windsock , Albatros Pub. Vol. 6, #4, July/Aug. 1990.
Windsock, Albatros Pub. Vol. 6, #5, Sept/Oct. 1990.
Windsock, Albatros Pub. Vol. 8, #1, Jan./Feb. 1992.
Windsock, Albatros Pub. Vol. 9, #4, July/Aug. 1993.

Please remember, when contacting retailers or manufacturers, to mention that you saw their products highlighted here - on AEROSCALE

Click here for additional images for this review.

SUMMARY
Highs: Excellent details, unconventional fuselage assembly alernate radiator pieces.
Lows: Black & white only instructions. No engine of any kind. Eduard's description of camouflage colours is one of their weakest areas. One piece molding of the flooring and its fixtures is a real short coming.
Verdict: This a good kit and filled the void that has been empty for so many years since the DML kit disappeared from LHS shelves. The modeler needs good colour information. But the kit is a high quality attempt.
  DESIGN & DETAILS:96%
  CAMO COLOUR INFORMATION:82%
  DECAL CHOICE:95%
Percentage Rating
91%
  Scale: 1:48
  Mfg. ID: #8196
  Suggested Retail: $34.95 USD MSRP
  Related Link: French multi colour camouflage 101
  PUBLISHED: Sep 19, 2008
NETWORK-WIDE AVERAGE RATINGS
  THIS REVIEWER: 90.97%
  MAKER/PUBLISHER: 88.44%

Photos
Click image to enlarge
  • Eduard 1/48 #8196
  • Eduard 1/48 #8196
  • Eduard 1/48 #8196
  • Eduard 1/48 #8196
  • Eduard 1/48  #8196
  • Eduard 1/48  #8196
  • Eduard 1/48  #8196
  • Eduard 1/48  #8196
About Stephen T. Lawson (JackFlash)
FROM: COLORADO, UNITED STATES

I was building Off topic jet age kits at the age of 7. I remember building my first WWI kit way back in 1964-5 at the age of 8-9. Hundreds of 1/72 scale Revell and Airfix kits later my eyes started to change and I wanted to do more detail. With the advent of DML / Dragon and Eduard I sold off my ...

Copyright ©2019 text by Stephen T. Lawson [ JACKFLASH ]. Images also by copyright holder unless otherwise noted. Opinions expressed are those of the author(s) and not necessarily those of AeroScale. All rights reserved.



Comments

Well here is the build halfway through Wednesday evening.
SEP 09, 2009 - 11:01 PM
Then at the evening's end.
SEP 09, 2009 - 11:02 PM
Excellent job done on the rigging Stephen Looking forward to seeing her done !
SEP 10, 2009 - 01:29 AM
Final touch-ups later this evening.
SEP 11, 2009 - 04:24 PM
As promised the end is here. Finished I say finished! With this build anyway. Here is the end of this tail uh er tale! STL
SEP 12, 2009 - 12:45 AM
That's absitively beautiful! The SPAD has always been one of my very favorites and that is a well-executed example! I doff my flight helmet in awed respect!
SEP 12, 2009 - 01:05 AM
Stephen , I must say this is one of your best builds so far !! Wow what a fantastic job done on her . Your solution to the rigging will be most helpful for others Very well played ! Since I joined the site I have notice that your finishing has also improved as well , thanks for being a visual teacher
SEP 12, 2009 - 04:02 AM
Thank you Michael and Terri. Its easy to do your best when it is appreciated. Model On! For me adding a relevant figure helps bring a visual proportion to the display. Here with Eduard's 1:48 #8196 Spad XIII build I use the Model Cellar French officer.
SEP 13, 2009 - 02:48 PM
Truly a beautiful job, Stephen!
SEP 15, 2009 - 08:44 AM
   

What's Your Opinion?


Photos
Click image to enlarge
  • 1/48 Eduard Spad XIII
  • Ed_SPADXIII_Parts_2
  • Ed_SPADXIII_Parts_1
  • Ed_SPADXIII_Parts_3
  • Ed_SPADXIII_Etch
  • Ed_SPADXIII_Clear
  • Ed_SPADXIII_Decals
  • Ed_SPADXIII_Axle
  • Ed_SPADXIII_Cowl
  • Ed_SPADXIII_Radiator_Core
  • Ed_SPADXIII_Propeller_2
  • Ed_SPADXIII_Propeller_1
  • Ed_SPADXIII_Radiator_Vanes
  • Ed_SPADXIII_Vent
  • Ed_SPADXIII_Nose
  • Ed_SPADXIII_Cowl_Panel
  • Ed_SPADXIII_Decking
  • Ed_SPADXIII_Sidewall
  • Ed_SPADXIII_Machine_Gun
  • Ed_SPADXIII_Cockpit
  • Ed_SPADXIII_Piping
  • Ed_SPADXIII_Seat
  • Ed_SPADXIII_Wheel
  • Ed_SPADXIII_Rib-Stritching
  • Eduard 1/48  #8196
    In the early stages
  • Eduard 1/48  #8196
    In the early stages
  • Eduard 1/48  #8196
    Here is a comparison between the DML flooring (Top)And the Eduard Flooring (bottom).
  • Eduard 1/48  #8196
    Basic colours to basic cockpit cmponents
  • Eduard 1/48  #8196
    Basic colours to basic cockpit cmponents
  • Eduard 1/48  #8196
    Basic colours to basic cockpit cmponents
  • Eduard 1/48  #8196
    Basic colours to basic cockpit cmponents
  • Eduard 1/48  #8196
    Basic colours to basic cockpit cmponents
  • Eduard 1/48 #8196
    Cockpit pieces and views.
  • Eduard 1/48 #8196
    Cockpit pieces and views.
  • Eduard 1/48 #8196
    Cockpit pieces and views.
  • Eduard 1/48 #8196
    Cockpit pieces and views.
  • Eduard 1/48 #8196
    Cockpit pieces and views.
  • Eduard 1/48 #8196
    Cockpit pieces and views.
  • Eduard 1/48 #8196
    Cockpit pieces and views.
  • Eduard 1/48 #8196
    Cockpit pieces and views.
  • Eduard 1/48 #8196
    Cockpit pieces and views.
  • Eduard 1/48 #8196
    Cockpit pieces and views.
  • Eduard n1/48 #8196
    Cockpit bits and pieces & views.
  • Eduard n1/48 #8196
    Cockpit bits and pieces & views.
  • Eduard n1/48 #8196
    Cockpit bits and pieces & views.
  • Eduard n1/48 #8196
    Cockpit bits and pieces & views.
  • Eduard 1/48  #8196
    Adding a heavily modified Karaya resin motor
  • Eduard 1/48  #8196
    Adding a heavily modified Karaya resin motor
  • Eduard 1/48  #8196
    Adding a heavily modified Karaya resin motor
  • Eduard 1/48  #8196
    Adding a heavily modified Karaya resin motor
  • Eduard 1/48  #8196
    Adding a heavily modified Karaya resin motor
  • Eduard 1/48  #8196
    Adding a heavily modified Karaya resin motor
  • Eduard 1/48  #8196
    Adding a heavily modified Karaya resin motor
  • Eduard 1/48  #8196
    Adding a heavily modified Karaya resin motor
  • Eduard 1/48  #8196
    Adding a heavily modified Karaya resin motor
  • 1/48 Eduard Spad XIII
    This the Nungessor scheme seen in period photos
  • 1/48 Eduard Spad XIII
    This the Nungessor scheme seen in period photos
  • 1/48 Eduard Spad XIII
    Paint schemes by manufacturer.
  • 1/48 Eduard Spad XIII
    Paint schemes by manufacturer.